Services
WSCAD design as a service
WSCAD capacity is harder to find than EPLAN capacity. The pool of designers is smaller, and most service providers do not run the system at all. Anyone whose plants are documented in WSCAD therefore needs no system change, but someone who works in it.
When this service is needed
- Your plants are documented in WSCAD and the capacity for it is missing.
- The previous WSCAD editor is leaving the company.
- Revisions pile up because nobody runs the system.
- A system change is being discussed although the documentation is good.
Result
- Maintained WSCAD project with article references
- Reports such as terminal plans, cable lists and parts lists
- Documented designation system
- Traceable revision states
We take on the electrical design there is no time for in house.
- Electrical design
- Since 1998
- Employees
- 15
- CAE systems (EPLAN, WSCAD, ELCAD)
- 3
- Projects since 1998
- 2,300+
Why FISEKON
One contact, not a distribution list
Whoever takes your project also works on it.
Your CAE system, not ours
EPLAN, WSCAD or ELCAD, using your part master.
Existing plants are our everyday work
Plant runs, documents do not match. That is where we start.
Capacity without a permanent post
Design capacity when you need it.
Process
How we work together
Clarify the requirement
Scope, WSCAD version, standard, deadlines. You receive a reliable assessment, usually within one working day.
Onboarding
We adopt your system and templates and document the state we find.
Design in rhythm
Fixed contacts, agreed delivery cycles, interim states in the WSCAD project.
Handover
You receive the complete project with drawings, article data and a revision state the next editor can build on.
We design and revise in WSCAD, from schematics and terminal and cable plans to reports. Your plants stay in the environment they are documented in. Changing systems merely because no editor can be found is the most expensive solution of all.
Onboarding runs as with any design in a foreign environment. We adopt your designation system, your templates and your article data and continue them consistently. What we find, we put in writing so the standard survives the next order.
The honest economics apply here too. An in-house WSCAD position is cheaper under a permanently full workload, but for WSCAD it often simply cannot be staffed. As a service you pay for the capacity your projects actually need, and cover for holiday and absence is built in.
If a migration does become due in the medium term, we say so openly and support it. Transferring legacy documentation into a new CAE system is a separate service with us. As long as the plant is in good hands in WSCAD, there is no reason for it.
Frequently asked
WSCAD design services
You have a technical task? We will look at how it can be solved.
Discuss a projectWhich WSCAD versions do you work with?
We work in the environment you run. The version is settled in the first conversation. What matters is not the version number but that your standard is continued consistently.
Is maintaining WSCAD worthwhile, or should we switch to EPLAN?
As long as your documentation in WSCAD is consistent and maintained, there is no technical reason to switch. A switch pays off when other reasons come in, such as customer requirements, merging several sites or expiring licences. We advise openly because we offer both paths, maintenance in WSCAD and migration.
Do you also take on ongoing maintenance?
Yes, on request under a maintenance agreement with a fixed allowance. Changes are reported and incorporated in an agreed rhythm instead of revisions piling up.
Related services
- Migration to EPLANMoving to EPLAN Electric P8 with a plan. The standard comes first, legacy projects are transferred as needed, and existing documentation is maintained until then.
- EPLAN design servicesExternal EPLAN design with an established team for schematics, cabinet layout and wire harnesses in Electric P8, Pro Panel and Harness proD.
- Maintenance agreementsOngoing upkeep of your documents at fixed terms, instead of a separate order for every change.
Contact
Tell us what it is about.
A phone call or three lines is enough. From the very start you talk to the people who will later work on your project, not to a distribution list.
Direct
- Phone+49 (0) 5247 4070-66
- Emailinfo@fisekon.com
- AvailabilityMon to Fri, 8 am to 5 pm CET
Or write to us
We usually reply within one working day.